Not sure what to buy? Check out my https://quadmeup.com/excellent-fpv-shopping-list/ Excellent FPV Shopping List!
Or become my Patron for special benefits https://www.patreon.com/pawelspychalski
INAV 2.1 is just behind the corner, so let’s take a quick look what is new in the INAV Configurator 2.1 (2.1.3 to be precise). And there:
* Configurator reconnect improvements
* Bing Maps as a map provider
* Additional visual hints for ESC protocol, gyro LPF and looptime
* Temperature framework
* CLI improvements
* and a few extra thingies
![JUMPBO 555-Q02 Quadcopter Speed Test [입문용 소형드론 야외 성능테스트]](https://quadcoptersource.tesb1.com/wp-content/uploads/2015/11/JUMPBO-555-Q02-Quadcopter-Speed-Test.jpg "JUMPBO 555-Q02 Quadcopter Speed Test [입문용 소형드론 야외 성능테스트]")
Pawel i have a question, how come when i go to port tab i dont see any ports anymore. The area where you can select ports is blank, empty
Pawel, thank you for your efforts and making this wonderful firmware better and better.
Thanks for your tireless efforts on INav , et al.
Awesome work and great idea on the temperature sensors …. so as to create a new 360 degree cockpit with having more items in the OSD, it would be nice for one day to have iNav use 360 camera feeds and head or radio potentiometer tracking to view video feed and move around inside aircraft and have the OSD paint a virtual cockpit (driven by temples) where we can display our OSD data designed in sections mimicking an aircraft instrument panel 😉 thank you for all you do.
Great stuff. Please do a video on inav and LIDAR 😀
Thanks Pawel. You’re awesome, we (the community) don’t deserve you
LM75 is linear temp sensor. It doesn’t work on I2C.
Thanks for the video… Pawel always have a excellent and empathic comunication
So… the baro have a temp sensor? I have a MATEK f405-CTR will try
Going to try inav on an old 5 inch frame
Thanks Pawel. Can you advise why I don’t see altitude hold mode? position hold, RTH and angle modes are ok. My quad running inav 2.1 (RC2 or RC3) on matek f405 ctr.
Thanks a bunch.
You’re awesome, man.
Have to go back to 2.1.1 to get GPS plus code in OSD. Last two release I can’t find it. GPS plus code is excellent and space saving. I record every flight in the goggles and it is much easier to use than lat long because of size requirements on screen.
Keep up the great work. I LOVE INAV.
Just Thanks 🙂
Paweł, is it possible to assign stability gain to a channel so you can increase and decrease the gain of the stability modes in the air?
Great video. I see the Mamba F405 and F40 4in1 ESC combo in your quadmeup shopping list. But I cannot see that one in the INAV list of boards. In Betaflight I used FURYF4OSD for the Mamba combo and it works well but I cannot find FURYF4OSD in the INAV list off boards either. I have just ordered the ALFA Monster 7 inch frame and I plan to use the Mamba combo on that one.Are there any plans to add it?
hi there , i have fo
Fitted the Matek wing in an Opterra , when engaging Failsafe , RTH the throttle is just to low , is the setting the one above the RTH selection as it shows 1000, if i set it to say 1400 the throttle on th failsafe does seem to raise up to that setting . IS this the way to set the RTH failsafe throttle ?. With your fantastic input to this hobby i have joined your Patreon subscription , well deserved.
I have one problem with the flight controllers , the USB connector is so easy to get broken off , at least there is another com port we can use , using an FTDI interface . I switch to that strait after flashing the board.
Can you add ability to load and save waypoints to pc?
Hi Pawel, is it possible to configure differential ailerons in INAV?
temperature support is nice for big aircraft