INAV Configurator Servo Mixer GUI – simply manage smix rules04:12

Not sure what to buy? Check out my https://quadmeup.com/excellent-fpv-shopping-list/ Excellent FPV Shopping List!
Or become my Patron for special benefits https://www.patreon.com/pawelspychalski

New version of INAV and INAV Configurator will pack a lot of goodies. Like this simple GUI to manage custom servo mixer rules. Instead of typing smix command in CLI, just click it. And you do not have to remember what each and every Input number means. Pretty sweet.

Category: Fail, Quadcoter Videos
    1. Boris Plate

      Perfekt ! I wish a Mission Planner in INav Configurator . I hate the Ez Gui!

    2. Peter Hancox

      Excellent news, thank you Pawel

    3. Petmen Petmen

      will motor 2 also be a servo Chanel??

    4. UAV Tech

      U the man! Thank you for all that you do!!

    5. Michel PASTOR

      Very nice

    6. Peter Hancox

      Here’s an issue. INAV configurator vs 1.9 (just out) and INAV Firmware 1.8 Ominbus F4 Pro. Start fresh setup. Goto CLI type smix reset, save. Goto servos GUI and setup for just stab role, i.e outputs 3 and 4 to drive control surfaces 4 and 5 (ailerons) for AIRPLANE, save. All works nicely. Now goto the CLI, type smix and look at what is there, it looks to be correct. At this point IF you hit SAVE in the CLI the controller will now control only one stab role aileron and also the pitch (elevator) yet this is not what the CLI shows, as nothing has changed. The only fix is to goto the CLI again and type smix reset and start over. Very weird???????

    7. Peter Hancox

      Discovered the issue below while trying to set up TWO stage FLAPerons, anyone with any clues how to go about 2 stage (position) flaps. Have plenty of RX channels to drive FC, using X4R. Thanks

    8. JMBB- FPV

      Hi I have a question about this cli text , does this work or act like Anti Gravity feature of betaflight ? The line cli;
      set Inav_gravity_cal_tolerance = 5

    9. JMBB- FPV

      Does this act like antigravity

    10. JMBB- FPV

      Thanks I have another item, I’ve set up INav for my chameleon 6 inch primarily for acro flight with the safety net of Gps RTH. I’ve kept the filters on the default values. Now I checked when I loaded the preset 5 inch racer values the filters have changed . In fact from very low values to larger values. I will test I wonder how much improvement will the filters be on my quad .

    11. JMBB- FPV

      How can I send you some screen shots of my filter settings

    12. Christian Mix

      please help me, I have a sky surfer, with f3 omnibus, everything is working perfectly, fail safe, rth, stalize, everything ok, just when active the flaperon the aileron goes up, and I want it to go down, I did not find nothing in the inav documentation how to flip flaperon, do you have any idea how I can do this?

    13. Elecifun

      Hi. I have been working on the servo setting for days in iNAV 1.9.2 using a SP Racing F4 EVO. I am suppose to be using servo setting for the motor/ The best I can get is servos working but as I increase the motor and use the rudder the rudder will not centre until I drop the motor to zero. Any ideas please?

    14. Elecifun

      Pawel, one more quick question please. If I use a Y adaptor on aileron servos (countering each other) will it cause me problems in INAV STAB mode, tuning ETC? Thanks.

    15. Derrick Mitchell

      I am using a SP Racing F3 on a Fixed Wing and for some reason unknown to me I can not get servo #4 to reverse so that the elevon will work. What am I doing wrong, I tried almost everything.

Related Posts

Enjoyed this video?
Share
Tweet
"No Thanks. Please Close This Box!"