BetaFPV Beta140 Maiden and Thoughts08:32

Hello everyone welcome back.

So the maiden went well. I did end up upgrading the antenna on the wolfwhoop vtx. If you have any questions about this build please leave me a comment.

Want to support my channel? Below are affiliate links. Affiliate links help me to earn a commission and are of no cost to you. So if you are out and online shopping click one of my links and it will greatly help me continue to do what I do.

Here is all that went into the build.

BetaFPV Betas 140 Carbon Fiber Frame
Beta140 140mm FPV frame is ture X structure, made of carbon fiber frame, integrated 2.5mm carbon fiber unibody main plate
Design for 3 intch propeller, fit for 1306/1407 motor
Fit for flight controller with the mounting hole of 20*20mm
Frame weight is 35g only
https://amzn.to/2L6oHGV

Hobbymate 1306 3100kv Brushless Motors
Model: 1306
KV: 3100KV
Voltage: 2-4s Lipo
Motor Weight: 11.3g
http://hobbycool.com/hobbymate-1306-3100kv-fpv-racer-brushless-motor-2-pairs/?afmc=3c

HakRC 20×20 F3 Stack with a 4 in 1 20amp ESC
F3 flight control support CF / BF firmware ( by default BF 3.17 )
Support 2 – 4S power input
Support external LED and buzzer alarm
Comes with battery voltage detection
Support PPM / SBUS / DSM2 / DSMX receiver
Support OSD remote control
Integrated OSD: yes
Integrated BEC: 2A
Mounting hole space is 20 x 20mm
Specifications:
MPU: MPU6000
Microcontroller: STM32F303CCT6
BEC: 5V / 2A output
External LED: yes
External buzzer: yes
Product weight:12g
http://hobbycool.com/hakrc-mini-flytower-f3-flight-controller-with-4-in-1-20a-esc/?afmc=3d

WolfWHoop TX2
Supports 48 channels
Tiny and low weights: under 2.2g
Power switchable: 0mW, 25mW, 200mW
Built-in U.FL connector rather than SMA
One cool feature about this VTX is that 0mW, you can adjustable your Parameter during a race with zero interference with any neighbor active channels
https://amzn.to/2shWJRG

Gemfan 3052-3 Props
Weight: 1.65g (each)
Middle Mounting Hole: 5mm
Size: 3052, 3. 0x5. 2.
Suit for fpv 130mm 140mm frame.
Compatible with 1306-1806 brushless motors
https://amzn.to/2IYDu5L

Foxeer Lollipop Antenna
Root reinforcement design 360°protection
Low feeder loss,easy to install, can be bent at any angle maintain
Body adopt imported PC+ABS material, can withstand high strength impact
Double-jacket semi-rigid cable for heavy impact resistance
https://amzn.to/2L3pPv5

Foxeer Predator Micro 2
1000TVL
1.8mm
110 Degree
M8 Lens Super WDR
FPV Camera With OSD
DC5V-40V
Low Latency
https://amzn.to/2xmPzjY

BetaFPV 3s 450mah Lipo
Connector: XT30 plug
Size: 13*30*53mm, Weight: 44g
Continuous Discharge Rate: 35C
https://amzn.to/2swkXaj

Thank you for watching.

What I fly and what I use

BNF Beta85
http://amzn.to/2DLRLEy

BNF Beta75s
http://amzn.to/2EnfnfA

BNF BetaFPV Beta 65
BetaFPV Beta 65 Frame Kit
http://amzn.to/2iFx68l

BetaFPV Flight Controller with Frsky Receiver & BetaFlight OSD
http://amzn.to/2B0QeZ6

BetaFPV Flight Controller with DSMX Receiver & BetaFlight OSD
http://amzn.to/2j1f6cm

BetaFPV Z01 Camera
http://amzn.to/2j4aKBh

BetaFPV 230mah LiHV Batteries
http://amzn.to/2kwVVqY

BetaFPV Replacement Canopies
http://amzn.to/2BewWzT

BNF Beta 75s
http://amzn.to/2zNl0jl

BNF Beta 75
http://amzn.to/2hDXC59

Beta 65s
http://amzn.to/2yMK3Dz

FPV Goggles I use
http://amzn.to/2hEvVc4

Soldering Iron I use
http://amzn.to/2hDYvuv

I film all my videos with the Samsung Note 5
http://amzn.to/2ASPm5P

Thank you very much.

Fly Safe & Fly Often