Quadcopter X & HK KK2.0 FW V1.5 Vol.49 Test Flight08:44

SELF LEVEL     BEAUTIFUL

HOW DO YOU GET IT TO FLY THAT WELL?! i have it and mine is unstable and just generally terrible 🙁

What servo do you speak of? There is no servo on ur 450.

From where can I buy that micro water level? ?? Is this water level on ur quad?? Can u give me link.

What would happen if you put propellers 1045?

I have the same Issues with my 450mm / Quadricopter , this is the same frame showed in this video , mine is pretty heavy ( 1,116Kg : LiPo 5000mAh = 416g ), but With theyre settup my craft should be controlable , bullshit , it allways slide , or turn around it self ( around the yaw axis ) , and the self level is counting the birds when i fly because it control apparently nothing … I plan to buy an APM 2.6 because I’ve a lot of shields that I can use it with APM , like GPS or some gyro and magneto in shield design … but I would like to know why my 450 doesn’t fly like this one … ( allready 50 or more hours to try to set up this board and nothing change … even after balancing ALL the components , and insolate the board from the frame …

Well 🙂 Can you share your PI settings and autolevel settings , to compare with mine , I think I have some vibration issues with my quad , so I would like to test the last settings and if there is no changes , I will rebuilt all , with vibration absorbers , new balanced props , and perhaps another flight controler , I would like to test APM 2.6 as I already have FPV system I will have telemetry returns , and many informations too , and I will be able to connect external Acc and Gyro and dataloger with my Arduino embed on the quad to record some information, as I already work around Arduino This will be easier , cause I allready have some shields to do that 🙂 

Yep 🙂 These are pretty the same :
Roll/pitch
Pgain:75 ; Plimit 100 ; I gain 32; I limit 20
Yaw :
Pgain : 100 : Plimit 20; I gain 40 ; I limit 20
Stick scaling :
roll / pitch  30 ; Yaw 50 ; Throttle : 90
Self level :
P gain 100 ; P limit 20
But I never Find anybody who can tell me about the value LIMIT in every settings … What is this ??? Limit of What ?
At this time , for me If I put 80 for P gain and limit at 100 what is the value of this limit ? 100 potatoes ? 100 Percent ? and what is the min and the max value we can put in any setting … Did you see this information anywhere ?
Cause I don’t undestand what does the limit value do … perhaps my problem start here , If I understand this value perhaps I’ll find where is my problem and solve it …
I juste notice that Higher P gain is , better the craft respond to my stick , but I ( integer ) I don’t know … If I put 30 in I gain does this mean that the reaction against wind or something else would append 30 seconds after ? or 30/100 seconds ? I tried to let the I gain at 0 , then I don’t see any changes to the flght … Last thing , perhaps my board is wrecked … duno 🙁

hi.. sorry if i disturb you i saw her in youtube you fly this kk2 board.. may i ask you a question..  because i need your advice or help.  what esc you put in your  Quadcopter OPTO or ESC with BEC? Because l’m new on this kk2 board.. for example if i use 4 esc Opto i put something like a 5 volts 3Amps  for power in this board?  second question if i used  4 esc with BEC  i put directly on this board or i take off 3 red wire of esc and one esc i remain with BEC for one power to kk2 Board.  just reply me if you have time or you cant sent your message on my email thanks

Olá, sabe me dizer se a placa cc3d tem essa Função?

Just wanted to thank you, with your settings my Q450 is 500% better, with the default settings my quad was all over the place.

My components:

Q450 v3 frame
Emax MT2213 935 Kv motors
Mistery 30A ESCs
3000 mAh battery (20c Turnigy)
Orange receiver (FASST)
KK 2.1.5 with 1.19S1 firmware

Although I balanced the props, did all the FC calibrations it was all over the place, now is way, way better.

Thanks again for sharing

Using that battery and controller do u need something to get volts under 6?

I respect you
I benefit from your videos
Could
I use the same settings to blow the hexacopter
Thank you

Sorry for my late reply.I appreciate your comments.I am going to make Hexacopter in next week.Thank you

I have KK2.1 V1.6++ , Can Your settings will work for me to fly this much stable and smooth….?

Mine also behaves similar on Auto level, i havent checked if its M1 or not, but it sometimes starts its slow acceleration, and its very twitchy on Autolevel, (maybe bad PID settings?)

Thank you for your comment.
Execute “acc calibration”.

Can you share PID value and self level values?

hello, I have a problem with my kk, I fly forward with the stik in the center, the two front engines 1 and 2 do not respond to the inclination forward, what depends on it?

Nice ace combat soundtrack <3