Realacc BOBO 95mm Micro Brushless Quadcopter Build Video05:14

Eachine minicube:
TX03 AIO camera:
JST connectors:
2s lipos: ||
8% off coupon code: toysho


Brand: Realacc
Item Name.: Bobo
Wheelbase: 95mm
Top board thickness: 1mm
Bottom board thickness: 1.5mm
Net weight: 13.8g
Motor mounting hole: 9×9
Flight control mounting hole: 20×20

Recommend parts:
Motor: 1104
ESC: 6a-20a
Camera: Transmitter camera combo
Transmitter: Transmitter camera combo
Flight control: Piko 20*20
Battery: 2-3s 450mah
Remote control: X9D
Propeller: 2 inch 3-blade

Package included:
1 x Realacc Bobo frame kit
12 x M3*6 Screw nuts
3 x M3*20 black aluminum column
4 pairs Isolation column

Eachine Minicube 20x20mm Flytower Compatible Frsky Flysky DSM2/ DSMX Receiver F3 Blheli_S 10A ESC

Brand name: Eachine
Mount hole: 20mm*20mm
Size: 27mm*27mm*20mm
Weight: 9.4g

1. Eachine Minicube Receiver
1). Eachine Minicube DSM2/ DSMX satellite Receiver
Frequency range: 2.403-2.479Ghz
Input power: 5V
Response time: 22ms / 11MS
Resolution: 2048
Display method: LED
Operating voltage: 3.3V
Working current: 60MA
Size: 27mm*27mm*7mm
Mount hole:20mm*20mm
Weight: 3.1 g
Antenna length: 100mm
Data format: Serial port
Protoco: DSM2/DSMX
Distance: no ground interference (1 m from the ground ) 300m
Uses: indoor small aircraft.
Compatible Transmitters: DSM2 / DSMX series of remote control
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator

2). Eachine Minicube Flysky 8CH AFHDS2A receiver
Channels: PPM 8CH
Model type: Multi-rotor
Frequency range: 2.408-2.475GHz
2.4GHz system: AFHDS 2A
Work Mode: PPM
Transfer method: FHSS
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): 300m
Working current: 40mA
Size: 27*27*7mm
Mount hole:20mm*20mm
Weight: 3.1g
Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F

3). Eachine Minicube Frsky Compatible 2.4G 8CH Receiver:
Frequency range: 2.403-2.479Ghz
Channels: 8CH
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): 500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)

2. Eachine Minicube F3 6DOF Flight Controller:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Processor: STM32 F303 MCU
Sensor: SPI Sensor MPU6000
Built-in Betaflight OSD ( Batt voltage, RSSI , Artificial Horizon , Fly mode , -Flytime, Craft name etz.)
Firmware version: Betaflight 3.1 Dshot ready
Target: OmnibusF3

3. Eachine Minicube 10A BLHeli_S 4 In 1 ESC:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 2-3S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on

STM32 F303MCU + BLHELI_S ESC make your Operating feel more stabilly and silky
Jaw-dropping flight performance
LED_STRIP solder pin
Betaflight support
Acro mode / Air mode /Angle mode support
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
OSD Configuration has been include in BETAFLIGHT GUI
Radio Stick to control PID Tunes

Package included:
1 x Minicube Receiver
1 x Minicube F3 6DOF Flight Controller
1 x Minicube 10A BLHeli_S 4 In 1 ESC

Bookmark and Share
    1. Jonathan Denoo
    2. Gal Kremer

Enjoyed this video?
"No Thanks. Please Close This Box!"